Ford axle identification.

In 1977.5 Ford’s new F-250 axle now started to appear. This new axle was a high pinion, reverse cut, 8-lug Dana 44. This axle for the F-250 Dana 44 is slightly different than the F-100 & F-150 offered in 1977. The F-250 is a little wider than the F-100 & F-150, for the wider 8 bolt wheel pattern.6.7L Power Stroke Diesel - What is my Axle Ratio, 3J - All l l l l l I am trying to verify that my axle ratio is 3.55 (which it should be). I have the F-350 diesel, camper package. My fuel mileage is bad. On my driver side label, it says that my axle is a 3J . Not 35, or anything else, just 3J as in Jermany.The 12 Bolt Sterling Axle. The Ford Sterling axle has two generations, currently. And are relatively easy to identify if the axle and brakes were kept 100% stock. The Sterling 10.25″ axles have an 8 x 6.5″ lug pattern, came with drum brakes, and were only used in Ford trucks built between 1985 and 1997.Step 3. Locate the identification tags on the rear-end housing unit. According to the Dana/Spicer Corporations' "Roadranger" Illustrated Parts List, there are two identification tags, one located on the driver's side differential carrier and one on the passenger side of the axle housing. Both tags contain similar information, however, the axle ...Step 3. Locate the identification tags on the rear-end housing unit. According to the Dana/Spicer Corporations' "Roadranger" Illustrated Parts List, there are two identification tags, one located on the driver's side differential carrier and one on the passenger side of the axle housing. Both tags contain similar information, however, the axle ...

Mean Max. 14314 posts · Joined 2007. #8 · May 9, 2009. You'll want one from an Explorer. '95-'01 will get you rear disc brakes, earlier models will have drums. Look on the driver's door of the donor Explorer for the axle code on the VIN sticker. Explorer 8.8 Axle codes. 43 Open 3200 3.08. 41 Open 3200 3.27.

Ford Rear Axle Assembly Identification - Page 07: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass. '82-'83: 3.42: 8.5: L: 28-WFC-G: Capri, Mustang, Cougar 82 Fairmont, Zephyr, Granada 82 Lincoln Continental '82 Thunderbird 82: 3.08: 7.5: L: 28-Received 2,739 Likes on 1,330 Posts. Quote: Originally Posted by 99150. Count the bolts on the cover. 12 bolts, you have a 10 1/2" sterling. 14 bolts, you have a Dana M275. Also, if the fill plug is in the cover, you have a DANA. I don't *THINK* they put the 10.25 sterling in the F250. The 10.25 hasn't been in a F250 since 1997.

Clutch, Transmission, Differential, Axle & Transfer Case - Rear Axle Identification... - I have an 87 Ford F-250 with a 6.9 Diesel and am trying to figure out what axle it has in the rear. I am looking for a dana 60 to put in my mud truck and this axle looks about like a dana 60 although it is not a full-floating...301, 4001, 9, axle, c3ta, end, ford, formula, fourms, id, identification, numbers, rear, tag, trucks. 1948 - 1956 F1, F100 & Larger F-Series Trucks - 9" rear end axle tag identification - hi all new to the forum thing but i can not find anything anywhere on this code. if someone could please help. C3TA 4001 B 301 3 89 2HE That is what i could ...The first thing you should look for is the Safety Compliance Certification Label. It could be on any door panel, front or back. Look for the axle and note the code under the axle. By the axle ratio, you can tell what rear-end your Ford F150 has. For detailed information about the rear end of your truck, read this full article.It has a 440/727, 14 bolt FF rear, and possibly a dana 60 front (closed knuckle). It still has the original dana 24 transfer case. So the front axle has that reads 4.09 D4TA SA BOM is 603480-1. Column left, 19th entry: Dana 44-6EFGH / 4.09-1 / No Free Running Hubs or Limited Slip / 3,500 lbs. Front Axle Capacity.

Trace coolmath

The different types of early Ford axles are easy to identify by referring to the picture on the right, which was scanned from an old magazine article that was written by Neal East. The 1928-1931 Model A axles have a uniform curve from end to end. The spring perch bosses are 2 1/4 inches. 1932 axles were the first Ford axles to be made with a ...

Yep, that's a 49-56 rear axle. The other giveaway is the u-joint flange, that style u-joint disappeared in '56 also. The '57-58 9" housing had drain plugs, those were gone after that. Ford went back and forth on the case/housing fill, with housing fill being more common in trucks for some reason, but certainly not exclusive to them.One of the most common questions we are asked is how to tell if your Bronco has a Dana 30 or a Dana 44 Front End. Once you know what to look for, it is very simple to decipher between the two. The quickest way to tell is to look at the top of the steering knuckles where the Front End Housing is connected to the Knuckle.Ford Rear Axle Assembly Identification - Page 11: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: S157B: Ford F250SD, F350SD Pickup ‘99: 4.10: 10.50: L--S157C: Excursion '00 Ford F250SD, F350SD Pickup ‘99-01: …By decoding the axle code, you can determine the specific axle ratio of your Ford F150 truck. Examples: Here are a few examples to illustrate the relationship between axle codes and axle ratios: Axle Code – 3.55: Axle Ratio – 3.55. Axle Code – 4.10: Axle Ratio – 4.10. Axle Code – 3L: Axle Ratio – 3.15 (Limited Slip)409 = Print Number (Model Number) B = Revision Identifier (Change in Design) 3L73: 3L73 = 3.73 Ratio. L = Limited Slip. Absence of L = Open Differential. A 3.73 geared limited slip axle would be marked as : 3L73. An open differential would show 3 (space)73. 102 denotes the ring gear size. 10.25 inches.Ford part numbers typically have three components: the prefix (three or four alpha-numeric characters) then a dash, followed by the basic number, another dash, and then the suffix …

Contact. You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 15. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 15. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L.Ford Axle Code Chart. Code Ratio Capacity Maker Type Yr. 12 2.73 3800 FORD REG 1991. 17 3.25 3300 FORD REG 1971. 17 3.31 3800 FORD REG 1995. 18 3.08 3800 FORD REG 1991.When it comes to automotive maintenance and repairs, one area that often perplexes even seasoned mechanics is identifying the correct rear axle. The Dana rear axle is a popular cho...Dana models with similar gasket shapes include Dana 25, 27, 30, 60, 70, and 80 but you need access to the identification tag to confirm this. There are two identification tags in every Dana. The first one is located on the driver's side differential carrier and the second tag is usually cited on the passenger side of the axle cover.Clutch, Transmission, Differential, Axle & Transfer Case - Nodular 9" Identification - I went through all 11 pages related to the nod 9, and couldn't come up with an answer, so... I've been looking for positive proof that I have a true nodular 9 . About 10 years ago, I bought the differential after wearing out some...

1965 Ford Mustang Axle Information & Ratios. The first table is the code and gear ratio. If you know your axle tag number, simply go to the second table. Axle code: Ratio & type: 6: 2.80 open differential: F: 2.80 locking differential: …

The Ford Sterling 10-1/2" Rear Full-Floating Axle was introduced in 1999 along with the new Super Duty F250 and F350. It shares some parts with the similar 10-1/4" Sterling Rear Axle which Ford used from 1985 to 1997 in the F250 and F350. The 10-1/2" Sterling is equipped with disc brakes (with the possible exception of some very early ...The 9 inch is one of the easiest rear ends to narrow because usually you can respline the axles that you have and use them again. Agreed but only if the axles are not tapered. Like. S. scfalk Discussion starter. 32 posts · Joined 2012. #6 · Jul 7, 2012. 9 in rear end. I need it to be around 50 inches between backing plates.Check the code on the door jab, loooks to be 410 in front,which is pretty obvious. I have the code book that came with my truck,if u post the code. V131C = F-250/350 PU '87-'96 4.10, 10.25 ring gear, limited slip. 1987 - 1996 F150 & Larger F-Series Trucks - axle identification - i just pulled the axle tags from my truck and after some …Received 0 Likes on 0 Posts. Managed to stumble on this in the tech !! Not sure if it helps at all. But the data tag on the door will have the axle code. 4N for me. AXLE CODES: 37- 3.73. 3L- 3.73 LS. 41- 4.10. 4N- 4.10 LS.And it took less than two hours to swap it out. Pull your brakes off and support them. Slide out the old and in the new axle and bolt it back up. The wrecking yard will know what fits and what doesn't. $2700 is insane! Mike. 04 E-350 Ext. 6.0L PSD 4.10LS 9700# w/driver. D70 Full floating rear axle from a cutaway van.1968 Ford Mustang Axle Information & Ratios. The first table is the code and gear ratio. If you know your axle tag number, simply go to the second table. Axle code: Ratio & type: 0: 2.50 open differential: 1: 2.75 open differential: A: 2.75 locking differential: 2: …Ford Rear Axle Assembly Identification - Page 06: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass., Mercury '67-'69: 3.10: 8 1/2 in: NL-Non-Removable Carrier: WER-AA: Ford Pass., Mercury '77-'78: 2.47: 8.75: NL: 28:CrownVic.net is a forum and information center dedicated to the Ford Crown Victoria and its siblings: Mercury Grand Marquis, ...The axle that came in that truck from the factory..... Dana 80 disc brakes 5.15 gears 10 on 7.25 bolt pattern 8 bolt axle stub Now the oddity... The 5 bolt axle stub really throws me off And the drum brakes, these trucks were ALL disc brakes it also looks like someone has put a set of 19.5 wheels/tires on as well

Geometry regents june 2018

Ford Axle Code Chart. Code Ratio Capacity Maker Type Yr. 12 2.73 3800 FORD REG 1991. 17 3.25 3300 FORD REG 1971. 17 3.31 3800 FORD REG 1995. 18 3.08 3800 FORD REG 1991.

Refer to our Ford axle identification charts to quickly Identify the parts and information you need. Each of our Dana 44 and Dana 60 front axle identification pages comes with diagrams and detailed specs and information on Ford front axles. Browse our Ford Dana axle identification pages and order your replacement parts online today.It is a banjo-style axle as is the 8-inch. It was in production on many Ford cars and trucks, first appearing in 1957 and finally replaced by the Salisbury-style 8.8-inch axle in 1986, saving about 50 pounds and boasting increased efficiency. Here is an example of a weld repair on a factory original housing.Early Bronco Front Axle Identification: Dana 30 vs Dana 44. The first generation Ford Bronco came with either a Dana 30 or Dana 44 front axle. The Dana 30 was used from 1966 to mid-year 1971. At this point in 1971, Ford made the switch to the beefier Dana 44 front end and continued this through 1977, the last year of the early Bronco.i just figured since you got the front, the rear was also 2000year model. you're right, its a 10.25. Personally since you already have metric up front, id sell that axle and just get a 1999+ 10.5" rear (same thing) with discs and metric pattern. Shop.FarmboyFabrications.com. 239.337.LIFT.Check the axle code on your door jamb. 99r is the code for the wide one I found written on another site. ... Ford Powerstroke Diesel Forum. 5.4M posts 267.7K members Since 2005 A forum community dedicated to Ford F-series owners and enthusiasts with a Power Stroke diesel engine. Come join the discussion about …Fact:This was the first Sterling axle used under a Ford 3/4- or 1-ton pickup Found under: '85-'92 F-250 and F-350 Type: Full-float, semi-float (depending on gross vehicle weight)Originally Posted by BigBlue 94. My 99 e250 has a 24 axle code. I know it's an open 3.73 Dana 60. That follows ford code with a 2 digit numbered axle code being open and a letter /number digit code for limited slip. 1959 thru today: Two digit AXLE code. If the first digit is a letter: Limited Slip. Ford Rear Axle Assembly Identification - Page 01. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L. In 1977.5 Ford's new F-250 axle now started to appear. This new axle was a high pinion, reverse cut, 8-lug Dana 44. This axle for the F-250 Dana 44 is slightly different than the F-100 & F-150 offered in 1977. The F-250 is a little wider than the F-100 & F-150, for the wider 8 bolt wheel pattern.Which Rear Axle Assembly? I thought I had the answer to this, but I've seen lots of conflicting information on this topic. Can someone tell me definitively which rear axle my 2022 F-350, SRW, 4x4, SCSB, 7.3L gas, 4.30 e-locking, camper package truck will have. Sterling, or Dana M-275? Thanks guys! Well if it's a 6.7 or 7.3 then it will have the ...Originally Posted by m-chan68. homeschoolin, your DRW 2006 F-350 is equipped with a Dana 80 rear axle, and I am 100% positive on that. Wulfman, Dana S110 and S130 rear axles are for F-450/F-550 applications. The Ford Workshop Manual specifies 75W90 weight gear oil, for this rear axle. Thanks for the confirm.Identification: The "4" in the code indicates that the axle is a rear axle, providing power to the vehicle's rear wheels. This crucial information helps mechanics and enthusiasts distinguish it from other types of axles. ... How does the Ford axle code 4N affect fuel efficiency? A: The Ford axle code 4N is designed to improve fuel ...

How to quickly identify the exact specifications of your Ford differential housing. Full details on how to read and decode differential identification tags l...So you may well have a 1980 Escort Mk2 Timken axle with Capri Mk2/3 Atlas brakes. The drums appear to be the 1-3/4" wide shoe type (4-cyl), rather than the 2-1/4" wide V6 type. The upper clamps, yes, are for an ARB, which the Capri used after 1972 in place of radius rods (1969-72). Norm.If you want to use a beam axle, then I'd go looking for one of three donor trucks. Either a Chevy van, Ford Econoline, or '55-'59 Chevy truck. But remember when you use a donor axle you need to either build your mounts at a height that gives you the correct kingpin angle, or you will have to fabricate shims to adjust the kingpin angle on the axle.Instagram:https://instagram. fire in englewood florida today I've had people tell me it's a Dana 60 and others say it's a Dana 70. I see 248 stamped into the axle, 05, and 2014828 with a B under it. Check the door jamb sticker and see what is listed under AXLE then compare to this list. AXLE CODES. 1968-Present E-Series Van/Cutaway/Chassis - Axle identification - Hi, I have a 2013 E-350, and I'm trying ... andy murray net worth 2023 those are GM military axles out of a m211 truck. Will have either 6.20 0r 6.80 ratio, most were 620s ther good axles for pullin if you are under 1000hp they do make after market parts for them, axles,spools, but its limited stuff, if your planning on getting in big over 1000hp, go to the f 106 rockwell axles, there is a ton of aftermarket parts ... does ring work with homekit The number on the top left of this sticker in 610366-8. Using the same method to look up this number, we find that it is a Dana 35 from a Ford Explorer. Axle Tags & Door Stickers: You can also identify axles by their axle tags and the sticker in the door jamb of the vehicle it came from. Click HERE for more details.Ford Rear Axle Assembly Identification - Page 08: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WFG-A: Ford Pass., Mercury '70-74: 2.75: 9 in: L: 28-WFG-A: Ford Pass., Mercury 70-74: eastern regional jail berkeley county wv Chrysler 11.5” Rear. Chrysler 11.8” Rear. Dodge Dana 60. Chrysler / Dodge - Differential Identification Shop by your differential. Please select a rear end that matches your vehicle below. Chrysler has a wide range of front and rear ends! We carry everything from the 7.25" front and rear end parts, to the large 11.8" rear end parts for Ram ... baskin robbins accept ebt The 1976 and 1977 Ford Dana 60 had a standard spiral, 4.10 ratio gear set. Cover: 10 Bolt, 12" high. Ring Gear: 9-7/8", 12 Bolt. Suspension: Leaf spring. Axle Shafts: 1976-1977 had 1.25"-19 spline outer axle shafts and the external snap ring axle u-joint has 1-3/16" diameter cups. Knuckle Mounting: Open with Greaseable King Pins. cine bassett place Re: Axle identification. I think the internals are the same. The difference is the external appearance of the pigs head because it has the mounting points for the trailing arms on the top. And the tubes will have different mounts for the coil spring platforms too.1992-1997 Dana 60 Front Axles in Ford F-350 4x4 Trucks will typically have the Ford Build Code on a mylar decal affixed to the right axle tube. Also, the Dana Bill of Material Number (BOM) and Ford Build Code are stamped on a Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows) when the vehicle was … hawes firearms company los angeles california Ford Rear Axle Assembly Identification - Page 12. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.2017+ Super Duty - 2023 F350 axle ID - My sterling in my 2019 F250 had 12 bolts on the differential cover. The one on my 2023 has 16 bolts and massive tubes. ... Ford built axles have a fill plug tapped into the iron case, usually to the left side of the pinion snout. The case is drained by removing the lowermost cover bolt.The Ford Axle Code C1 plays a significant role in determining the acceleration, towing capacity, and overall performance of Ford vehicles. The gear ratio provided by this axle code directly affects how much torque is delivered to the wheels. The Ford Axle Code C1 has a direct impact on the power and torque output of the vehicle, influencing its ... how many tons in 3000 pounds It's where I found the picture. He has some excerpts from the 1981 manual, which would be the same as your 80. 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks - Rear axle id - Hi I'm trying to identify a rear axle in my 1980 f250 I have the door code B5 and tag from the rear 3 33 EOTA UD 603943-5 L S i have tried using Dana's ...Step 3. Locate the identification tags on the rear-end housing unit. According to the Dana/Spicer Corporations' "Roadranger" Illustrated Parts List, there are two identification tags, one located on the driver's side differential carrier and one on the passenger side of the axle housing. Both tags contain similar information, however, the axle ... heb cash check hours The right ratio. If the tag reads S806D the axle was made for a F 150 Pickup 87-95, E150 Van 87-95, Bronco 87-95. It is a 8.8 In. with a gear ratio of 3.08. It is also a unlocking diff. Hope this clears anything up. Ralph [email protected]. Reply Like. # 8. 09-18-2010, 03:03 PM. toyota camry 2000 fuse box diagram In 1977.5 Ford’s new F-250 axle now started to appear. This new axle was a high pinion, reverse cut, 8-lug Dana 44. This axle for the F-250 Dana 44 is slightly different than the F-100 & F-150 offered in 1977. The F-250 is a little wider than the F-100 & F-150, for the wider 8 bolt wheel pattern.Rear Axle identification HELP. Definitely need a little help here. I have a 2003 Ford F-150 FX4 Lariat Supercab with an 8 foot bed and the 5.4 V8. I'm trying to identify which axle I have, but the truck is giving me contradicting information. The axle code on the sticker inside the door says it's an H9, which is the 8.8" ring gear w/ 3.55 ratio. gas prices in iowa city ia In 1977.5 Ford’s new F-250 axle now started to appear. This new axle was a high pinion, reverse cut, 8-lug Dana 44. This axle for the F-250 Dana 44 is slightly different than the F-100 & F-150 offered in 1977. The F-250 is a little wider than the F-100 & F-150, for the wider 8 bolt wheel pattern.(mk2 cortina dampers mount in front of the axle casing on both sides). also, the handbrake cable pulley is used on the mk1 capri (although mk2 cortina used a similar system but that depended on whether a floor mounted or dash mounted handbrake was used). mk1 capri had anti-tramp bars, ford always fitted them above the axle. guess the bushes ...Assemble pinion mate cross shaft, make sure lock pin hole of the shaft is in verticle position and lined up with the lock pin hole of the case. Step (15) Assemble new roll pin. Peen metal of case over pin to lock in place. Step (16) Secure end yoke or flange with holding wrench, and remove pinion nut and washer.